clonezilla clone shutdown now pc boots to white screen | clonezilla won't boot

2024-11-21T07:25:06 | By , DOD blog

clonezilla clone shutdown now pc boots to white screen | clonezilla won't boot clonezilla clone shutdown now pc boots to white screen You will need to use your Windows installation DVD or Recovery USB or some third party utility to restore the bootloader. Bootrec is included with Windows, use fixboot and fixmbr commands. . $13K+

0 · clonezilla won't boot
1 · clonezilla not booting windows 10
2 · clonezilla image won't boot
3 · clonezilla cloned drive not booting
4 · boot from cloned partition blue screen

$3,299.00

I've just started using Clonezilla Live and have tried it out copying a 100MB boot partition from my Windows 7 PC. It boots up fine from the CD and goes through all the menus.

I've cloned both of these partitions with Clonezilla (partition to partition clone, not disk clone) to a new disk and then faced the same issue as OP when trying to boot from the .You will need to use your Windows installation DVD or Recovery USB or some third party utility to restore the bootloader. Bootrec is included with Windows, use fixboot and fixmbr commands. . I cloned my windows system partition /dev/nvme1n1p3 to the larger one /dev/nvme0n1p2 using clonezilla partition to partition clone. I created a bootable windows usb, .

When I manually boot a Windows recovery environment and then try to boot from the HDD, it just bluescreens. Bitlocker is disabled. Notes. I cannot figure out what's causing .I plugged in my 2 hard drives into the SATA ports inside my computer, and booted Clonezilla from a USB. Ran through the Expert screens and chose: -g auto (reinstall grub on target hard disk . Next I restarted my computer with the loaded USB flash drive and the SSD connected to the computer while tapping F12. This brought up the boot menu and I picked . I was cloning my HDD using bootable Clonezilla ( disk to disk) when the power went out, I retried after the power came back only for it to turn off again during cloning. third .

I'm trying to backup my internal SSD, I created a bootable USB drive with Clonezilla, I'm able to get to the initial Clonezilla screen with the white background and orange . I've just started using Clonezilla Live and have tried it out copying a 100MB boot partition from my Windows 7 PC. It boots up fine from the CD and goes through all the menus. I've cloned both of these partitions with Clonezilla (partition to partition clone, not disk clone) to a new disk and then faced the same issue as OP when trying to boot from the clone. The solution was to boot into recovery mode, then command line.

You will need to use your Windows installation DVD or Recovery USB or some third party utility to restore the bootloader. Bootrec is included with Windows, use fixboot and fixmbr commands. There are many pitfalls to disk cloning, but from my experience this is most likely the issue. If you try to boot from the drive cloned by Clonezilla, but Window 10 not booting, you can try to repair Windows Startup in Windows recovery environment (Windows RE). The Windows Startup repair will fix some errors and help you boot successfully. As I said above, I can work around these problems by using the Win 8.1 Repair cd to effect a proper shut down and I can run the four commands of "bootrec /FixMbr" to fix the MBR of the new clone so that it boots properly. I cloned my windows system partition /dev/nvme1n1p3 to the larger one /dev/nvme0n1p2 using clonezilla partition to partition clone. I created a bootable windows usb, went to the command prompt and did:

I'm using clonezilla live, and the screen goes completely blank during boot. The last message on the screen is that it is: probing edd. I tried with the latest version and also with a two year old version of clonezilla. I plugged in my 2 hard drives into the SATA ports inside my computer, and booted Clonezilla from a USB. Ran through the Expert screens and chose: -g auto (reinstall grub on target hard disk boo sector) Next I restarted my computer with the loaded USB flash drive and the SSD connected to the computer while tapping F12. This brought up the boot menu and I picked USB Flash Drive and hit enter. Next, the screen goes dark .

clonezilla won't boot

I've just started using Clonezilla Live and have tried it out copying a 100MB boot partition from my Windows 7 PC. It boots up fine from the CD and goes through all the menus. I've cloned both of these partitions with Clonezilla (partition to partition clone, not disk clone) to a new disk and then faced the same issue as OP when trying to boot from the clone. The solution was to boot into recovery mode, then command line.

If you try to boot from the drive cloned by Clonezilla, but Window 10 not booting, you can try to repair Windows Startup in Windows recovery environment (Windows RE). The Windows Startup repair will fix some errors and help you boot successfully. As I said above, I can work around these problems by using the Win 8.1 Repair cd to effect a proper shut down and I can run the four commands of "bootrec /FixMbr" to fix the MBR of the new clone so that it boots properly. I cloned my windows system partition /dev/nvme1n1p3 to the larger one /dev/nvme0n1p2 using clonezilla partition to partition clone. I created a bootable windows usb, went to the command prompt and did:

When I manually boot a Windows recovery environment and then try to boot from the HDD, it just bluescreens. Bitlocker is disabled. Notes. I cannot figure out what's causing this, since both scenarios throw no errors in Clonezilla, but something went wrong after introducing this feature in #205. I'm using clonezilla live, and the screen goes completely blank during boot. The last message on the screen is that it is: probing edd. I tried with the latest version and also with a two year old version of clonezilla. I plugged in my 2 hard drives into the SATA ports inside my computer, and booted Clonezilla from a USB. Ran through the Expert screens and chose: -g auto (reinstall grub on target hard disk boo sector)